Overview

The DPA 5006A is a complete DPA 4006A Surround Kit with five carefully factory-matched omni microphones. Even though the standard tolerances on the d:dicate Recording Microphones are extremely low, the surround match is even closer. The specially selected DPA 4006A microphones are matched within +/-0.5 dB on both frequency response and sensitivity from mean of set. The maximum phase response difference is 5deg.. The natural sound, high sensitivity, low noise-floor and extremely linear frequency response from 10 Hz to 20 kHz (+/-2 dB) of the microphones make the DPA 4006As the perfect choice for all AB Stereo, Decca Tree or surround main array recordings. The precise reproduction, total transparency and natural-sounding clarity of a DPA 4006A microphone will provide you with a lifetime of satisfying listening. The foam design in the heavy-duty transportation box allows for fast and easy exchange of microphone/accessory.

Included in this kit
Carefully matched microphones, sturdy Peli case, holders, grids and windscreens.

Features

• Three + two carefully matched microphones
• Decca Tree front + cardioids rear
• Specially useful as orchestral main pair
• Peli Case transportation and protection

Specifications

• Directional characteristics:
• 4006A: omnidirectional
• 4011A: cardioid.
• Principle of operation:
• 4006A: pressure
• 4011A: pressure gradient.
• Cartridge type: Pre-polarized condenser
• Frequency range: 10 Hz to 20 kHz
• Frequency range, ± 2 dB:
• 4006A: 10 Hz to 20 kHz
• 4011A: 40 Hz to 20 kHz.
• Sensitivity, nominal, ±2 dB at 250 Hz: 4006A: 40 mV/Pa; -28 dB re. 1 V/Pa
• Sensitivity, nominal ±2 dB at 1 kHz: 4011A: 10 mV/Pa; -40 dB re. 1 V/Pa
• Equivalent noise level, A-weighted:
• 4006A: Typ. 15 dB(A) re. 20 µPa (max. 17 dB(A)).
• 4011A: Typ. 18 dB(A) re. 20 µPa (max. 20 dB).
• Equivalent noise level, ITU-R BS.468-4:
• 4006A: Typ. 27 dB (max. 29 dB)
• 4011A: Typ. 25 dB (correct with the attenuator in 0 dB or -20 dB setting).
• S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL:
• 4006A: Typ. 79 dB(A)
• 4011A: Typ. 76 dB(A).
• Total Harmonic Distortion (THD): < 1 % up to 139 dB SPL peak
• Minimum load impedance: 2 kohm
• Dynamic range:
• 4006A: Typ. 124 dB
• 4011A: Typ. 121 dB.
• Max. SPL, peak before clipping:
• 4006A: 147 dB
• 4011A: 159 dB.
• Switchable attenuator: 0 dB / -20 dB
• Output impedance: < 200 ohm
• Cable drive capability: 100 m (328 ft)
• Output balance principle: Impedance balancing with Active Drive
• Common Mode Rejection Ratio (CMRR): > 60 dB
• Power supply (for full specifications): 48 V Phantom power (± 4 V)
• Current consumption: 2.8 mA
• Connector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
• Color: Matte black
• Weight:
• 4006A: 163 g (5.7 oz)
• 4011A: 158 g (5.6 oz).
• Diameter:
• 4006A: 0.63 to 0.75" (16 to 19 mm )
• 4011A: 0.75" (19 mm).
• Capsule diameter:
• 4006A: 0.63" (16 mm)
• 4011A: 0.75" (19 mm)
• Length: 6.7" (170 mm)
• Output voltage, RMS: > 5 V
• Polarity: +V at Pin 2 for positive sound pressure
• Temperature range: -40 °C to 50 °C (-40 °F to 122 °F)
• Relative Humidity (RH): Up to 90 %