There's no debate – when you choose Crown's XTi 2 Series you're choosing one of the most powerful and innovative amplifiers on the market today. That's because the all-new XTi 2 Series amps continue to set the standard for unmatched performance and value delivering the goods night after night without breaking a sweat.
Features:
•Peakx Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold attack and release
•Enhanced Subharmonic Synth section provides user control over frequency gain and filter type for system-specific tuning
•3 User-defined fan mode controls – normal early and fullspeed – for matching fan performance to a specific application
•New system monitoring provides software visibility of AC line voltage and power supply temperature
•Integrated cast-aluminum handles for easy handling and enhanced durability
•Locking power cord clip provides a secure connection between the amplifier and power cord
•Updated HiQnet Band Manager™ and System Architect™ control software
•Increased number of presets to a total of 50; 49 of which are user definable
Integrated Processing:
Input EQ
•6 parametric filters per channel with adjustable Q ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
Crossover Filters
•Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.
Output EQ
•8 parametric filters per channel with adjustable Q ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
Delay
•For signal alignment of driver; 50 mS of total delay.
SubHarmonic Synth
•Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency gain and filter type.
Peakx™ Plus Limiter
•User defeatable limiter that allows users to control Threshold Attack and Release times.
Presets
•50 total presets 49 of which are user-definable.
Input/Output Connectors
•Input Connectors: XLR one per channel
•Link/Out Connector: Loop-thru signal from input connector for linking another amplifier one per channel.
•Output Connectors: Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
•HiQnet™ USB Connector: Type B connects to HiQnet™ network.
Specifications:
| Sensitivity (volts RMS) for full rated power at 4 ohms |
1.4V
|
| Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
|
| Signal to Noise Ratio (below rated 1 kHz power at 8 ohms), A-weighted |
100 dB (103 dB in XTi 6000)
|
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
|
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors. |
| AC Line Current (120VAC amplifier playing 1/8 power pink noise into 4 ohms per ch) |
XTi 1000: 6.8A, XTi 2000: 8.3A, XTi 4000: 10.5A; at idle draws no more than 30 watts.
XTi 6000: 15.3A; at idle draws no more than 180 watts. |
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
|
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
|
| Load impedance (note: safe with all types of loads) Stereo Bridge mono |
2-8 ohms (4-8 ohms in XTi 1000 A1 100V versions)
4-16 ohms (8-16 ohms in XTi 1000 A1 100V versions) |
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
XTi 1000: 30.5 dB. XTi 2000: 32.9 dB. XTi 4000: 34.2 dB. XTi 6000: 37.1 dB.
|
| Maximum Input Signal |
+22 dBu typical
|
| Operating Temperature |
0° C to 40° C at 95% relative humidity
(non-condensing) |
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V, 220-240V 50/60 Hz
|
| Ventilation |
Flow-through ventilation from front to back
|
| Cooling |
Heat sinks and proportional-speed fan
|
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B) x 3.5 in. (8.9 cm) H x12.25 in. (31.1cm) D
XTi 6000 is 16.2 in. (41.15 cm) D |
| Net Weight, Shipping Weight |
18.5 lb (8.4 kg), 21.5 lb (9.8 kg)
XTi 6000 is 24.0 lb (10.9 kg), 30.0 lb (13.6 kg) |
