- Color-calibrated QUAD color LEDs (8 LEDs/ft)
- Homogenous color mixing
- Round diffuser for soft appearance and extended viewing angle
- Dedicated color temperature control channel (1800K - 12000K)
- Selectable segment modes (1, 4 or 8 segments)
- Selectable power consumption (12W/10W/5W) per foot
- Integrated multi-range power supply unit (PSU) 100-277V for long fixture runs
- Hybrid power and data connector for easy daisy-chained configurations
- DMX and RDM control
- Integrated magnetic switch for local diagnostics
- Rugged IP66 housing designed for permanent outdoor installations
- Low weight 0.8 kg/ft (1.9 lbs/ft)
- Compact design - 40mm (1.57 inch) width
Specifications
Physical
- Width: 40 mm (1.57 inch.)
- Height: 84 mm (3.31 inch.)
- Length - 1 ft Version: 312mm (1.02 ft)
- Weight - 1 ft Version: 0.85 kg (1.9 lbs)
Dynamic Effects
- Color mixing: RGBW
- Color temperature control: 1800K – 12000K in 50K steps (default 4000K)
- Intensity: 0 - 100%
- Segment Control: 0.5ft, 1 ft or full 4 ft fixture control
Control and Programming
- Control systems: DMX, RDM
- Control resolution: 8-bit DMX individual color control
- User interface: Magnetic button to call up fixture status and test fixture
- Stand-alone control: Up to 20 scenes with individual fade/hold times
- DMX compliance: USITT DMX512/1990
- RDM compliance: ANSI/ESTA E1.20
- Dimmer Resolution: 16-bit DMX control of intensity
- DMX channels 4ft: 6/4/3/12/24 (standard/RAW/1 seg/4 seg/8 seg)
- DMX channels 1ft: 6/4/3/6 (standard/RAW/1 seg/2 seg)
Optics
- Light source: QUAD color LED (8 LEDs per foot)
- Minimum LED lifetime: 50 000 hours (to >70% luminous output)*
- Beam angle: 180°Binning: Tight color and flux binning
- Calibration: Full Gamut Color Calibration (1 step MacAdam ellipse)
- *Figure obtained under manufacturer's test conditions
Construction
- Housing: Aluminum
- Finish: Clear anodized (standard) or optional colors on request
- Front: Clear polycarbonate
- Protection rating: IP66IK rating: IK08
- Effective Projected Area (EPA): 0.04 m2 per ft
- Corrosion resistance: C5 - very high corrosivity / Durability Range: High (ISO 12944-6)
- Vibration resistance: 1.0g, Sinusoidal (IEC 60068-2-6), 0.7g RMS Random (IEC 60068-2-64), 3.0g (ANSI C136-31)
Installation
- Orientation: Any
- Minimum distance to illuminated surfaces: 0.1 m / 0.3 ft.
Connections
- Power/data in/thru: 8-pin custom connectors
- Surge Protection: 4 KV
- Maximum connected 4 ft fixtures *: 42 pcs (52 m /169 ft) @ 230-277 V
- Maximum total string length (cable + fixtures)*: 150 m / 328 ft
- * Refer to system diagram for details on fixture run limitations.
Electrical
- AC power: 100-277 V AC nominal, 50/60 Hz
- Power supply unit: Auto-ranging electronic switch mode
- Typical half-cycle RMS inrush current at 230 V, 50 Hz: 0.35 A
- Typical earth-leakage current 1 ft: 0.15 mA
- Typical earth-leakage current 4 ft: 0.21 mA
- Power Factor 12 W / 10 W mode: 0.95 @ 100 V / 120 V / 208 V / 230 V / 240 V ,
0.90 @ 277 V - Power Factor 5 W mode: 0.90 @ 100 V / 120 V / 208 V / 230 V / 240 V , 0.70 @ 277 V
- Power Consumption 1 ft
- Maximum: 12 W / 10 W / 5 W *
- Idle: 1.54 W *
- Power Consumption 4 ft
- Maximum: 48 W / 40 W / 20 W *
- Idle: 2.30 W *
- * Measurements made at nominal voltage. Allow for a deviation of +/- 10%.
- Idle: steady state, all LEDs at zero intensity.
- Power Consumption: Depending on power setting mode.
Thermal
- Cooling: Convection
- Total heat dissipation (calculated, +/- 10%): 41 BTU/hr. per foot
- Maximum ambient temperature: 45° C (113° F)*
- Minimum ambient temperature: -30° C (-22° F)
- *Above this temperature, the fixture regulates output to protect from overheating
- Efficacy (max output): 37 lm/WLWR*: 529 lm/kg (237 lm/lb)
- *LWR = Lumen-to-Weight Ratio
Environmental
- RoHS: Compliant
- REACH: Compliant
- WEEE: Compliant
- Proposition 65: Compliant
- FSC: Certified cardboard inlay and outer packaging
Approvals
- Global CB Certification/IECEE: IEC 60598-2-5 (IEC 60598-1)
- EU safety: EN 60598-2-5 (EN 60598-1), EN 62471, EN 62493
- EU EMC: EN 55015, EN 55032, EN55035, EN 61547, EN 61000-3-2, EN 61000-3-3
- US safety: ANSI/UL 1598
- US EMC: 47 CFR Part 15 Class B
- Canadian safety: CSA C22.2 No. 250.0
- Australia/NZ: RCM
- India: BIS IS 10322(Part5/section5)