AMX NMX-ENC-N1115-WP-WH

AMX

AMX NMX-ENC-N1115-WP-WH

N1000 Series AV Over IP Decor Style Wallplate Encoder with KVM in White

SKU: AMX-FGN1115-WP-WH

MSRP: $1,915.00

MAP: $1,915.00

UPC:

Current Stock:

Quantity:

Description

The N1000 Series Encoders and Decoders are an affordable local AV-over-IP switching solution that packetizes video into a minimally compressed IP format that provides excellent video quality at low latencies. This compression is perfect for point-to-point video distribution, small 2x1 switching applications, and larger switching applications (for example, 32x32), all using off-the-shelf layer-3 network switches.

The NMX-ENC-N1115-WP provides the excellent encoding capabilities of the NMX-ENC-N1133 in a 2-gang wallplate format. This encoder can be easily mounted in a wall, lectern, or floor box using a standard 2-gang US back box, and connected to power and Ethernet using only a single category cable.

Common Applications

The NMX-ENC-N1115 is the perfect solution for any application and video matrix smaller than 32x32. Common applications include conference rooms, huddle spaces, and lecterns (inside or adjacent-to)

Features

Sub-Frame Latency – Combined encode and decode latency of 10 ms at 60 fps.
Minimal Proprietary Compression (MPC) – Visually lossless MPC algorithm applied applied to all resolutions
Wallplate Form Factor – Fits conveniently into a 2-gang US back box for easy installation in a wall, floor, or lectern.
Power Over Ethernet (PoE) – PoE eliminates the need for power supply
Unmatched Flexibility – Build point-to-point links, simple 2x1 switches, or cost-effective matrices up to 32x32.
Separate Inputs – Separate HDMI and VGA input connectors on the encoder

Specifications

Video	Digital Video Input: HDMI, DVI-D, Dual-Mode DisplayPort (DP++) Analog Video Input: HD-15 VGA, Component* Video Output: Video Output Formats: HDMI, DVI-D, Dual-Mode DisplayPort (DP++), HDCP content protection support, RGBHV, YPbPr Progressive Input Resolutions Supports most common HD up to 1920x1200. Interlaced Input Resolutions Supports 1080i60. Analog Input Resolutions NOTE: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz. Supports most common HD up to 1920x1200. Output Resolutions: Matched to inputs. Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels NOTE: The N1115-WP does not accept Composite or S-Video (YC). Color Space: 4:2:2 *These signal types are supported through a passive adapter.
Audio	Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo Output Signal Types: Ethernet Analog Audio Format: 8ch PCM, Stereo 2-channel Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz
Latency	Latency: 10 ms at 60 fps Bandwidth: 840 Mb/s (varies with resolution) Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency. Note: Scaling adds one frame of latency (17ms at 60fps).
Communications	Ethernet: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP HDMI: HDCP, EDID management
Ports	P0: 8-wire RJ45 female 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port Provides the network connection, network AV video, and power to the Encoders and Decoders HDMI IN: HDMI video input VGA IN: DB15 analog input USB IN - Host: USB-B host input USB IN - Maintenance: USB-Mini maintenance input
Controls and Indicators - Front Panel	RESET Button: Recessed pushbutton Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings POWER LED: On solid (green) when operating power is supplied (via PoE or local power supply) AUDIO LED: On (green) when audio is transmitting. ANALOG VIDEO LEDs: On (green) when analog source is available and transmitting. DIGITAL VIDEO LED: On (green) when video source is available and transmitting HDCP LED: On (green) when the source is using HDCP STREAM LED: On (green) when the unit is streaming video STATUS LED: Flashing (green) when the unit is active. LINK/ACT LED: Flashing (yellow) when network traffic is being sent or received.
Power Supply	Power over Ethernet Can be powered via a PoE switch or other equipment with a PoE source. Conforms to IEEE 802.3af Class 3 (802.3at Type 1) Point-to-point applications between the encoder and a decoder requires a PoE injector to power the wallplate encoder. Note: In order for the unit to receive Power over Ethernet (PoE), it must be connected to a switch or other equipment that has a PoE PSE (Power Sourcing Equipment) port. Warning: Do not run wiring that is connected to a PoE PSE port outside of the building where the PSE resides. It is for intra-building use only.
Environmental	Temperature (Operating): 32° to 104°F (0° to 40°C) Temperature (Storage): -22° to 158°F (-30° to 70°C) Humidity (Operating): 10% to 90% RH (non-condensing) Humidity (Storage): 0% to 90% RH (non-condensing) Heat Dissipation: Up to ~26 BTU/hr
General	Dimensions (HWD): 4.06" x 3.5" x 2.25" (10.31 cm x 8.84 cm x 5.72 cm) Weight: .75 lb (0.34 kg) Airflow: Natural convection via vent openings on front, back, and top Installation Mounts onto standard 2 gang US back boxes Mounts into standard décor style wallplates (not included) Regulatory Compliance: FCC, CE, and NTRL Recommended Accessories Compatible with NMX-ENC-N1222, NMX-ENC-N1233, NMX-ENC-N1512, and NMX-NVR-N6123 PS-POE-AT-TC High-Power PoE Injector, 802.3AT Compliant FG423-84)
FG Numbers	FGN1115-WP-WH (White) FGN1115-WP-BL (Black)