Video |
- Digital Video Input: Network video over Ethernet via RJ45 port or fiber via 1G SFP port
- Video Output: HDMI, DVI-D (through adapter)
- Formats: HDMI, DVI-D (through adapter), HDCP content protection support
- Output Resolutions:
- Supports most common HD up to 1920x1200.
- **720x480 @ 59Hz, 640x480 @ 60Hz, **720x480 @ 60Hz, **720x576 @
50Hz, 800x600 @ 56Hz, 800x600 @ 60Hz, **1280x720 @ 50Hz, **1280x720 @
59Hz, **1280x720 @ 60Hz, 1360x768 @ 60Hz, 1366x768 @ 60Hz, 1024x768 @
60Hz, 1280x800 @ 60Hz, 1152x864 @ 60Hz, 1600x900 @ 60Hz, 1440x900 @
60Hz, 1280x960 @ 60Hz, 1280x1024 @ 60Hz, ***1600x1200 @ 60Hz, 1680x1050 @
60Hz, 1920x1080 @ 23Hz, 1920x1080 @ 24Hz, 1920x1080 @ 25Hz, 1920x1080 @
29Hz, 1920x1080 @ 30Hz, **1920x1080 @ 50Hz, **1920x1080 @ 59Hz,
**1920x1080 @ 60Hz, **1920x1080i @ 50Hz, **1920x1080i @ 59Hz,
**1920x1080i @ 60Hz, ***1920x1200 @ 60Hz
**supported in component mode
***reduced blanking only |
Audio |
- Input Signal Types: Network video and audio over Ethernet via RJ45
(audio at 48-kHz, standard SVSI audio stream or AES67, user selectable)
- Output Signal Types: Embedded audio on DVI-D or HDMI (through adapter)
- HDMI Audio Formats: 8ch PCM
- Analog Audio Format: Stereo 2-channel
- Digital-to-Analog Conversation: 16-bit 32 kHz, 44.1 kHz and 48 kHz (matched to Encoder settings)
|
Latency |
- Video Latency: 10 ms at 60 fps
- Audio Latency: standard SVSI audio stream = 17 ms(synced to video); AES67 = <1 ms adjustable to 17 ms
Note: Video and audio latency values are the combined encode
plus decode latency. Total latency from source to screen will also
include any network latency.
Note: Scaling adds one frame of latency (17ms at 60fps) |
Communications |
- Ethernet:
- P0: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
- P1: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
|
Ports |
- +12V 2A: One 12 Volt DC power input
- P0:
- 8-wire RJ45 female
- 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
- Provides the network connection, network AV video, and power to the Encoders and Decoders
- P1:
- 8-wire RJ45 female
- 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
- IR:
- 2-pin terminal Phoenix connector
- Provides Infrared (IR) output only (33-60 kHz; typically 39 kHz). Emitter may be necessary (not included)
- RS232:
- 3-pin terminal Phoenix connector
- Provides a serial control interface. Full duplex communication. Available terminal speed settings: 9600-115200 baud rate
- Audio:
- 5-pin terminal Phoenix connector
- Provides user-selectable balanced/unbalanced output. Dedicated audio output
- HDMI Out: HDMI video output
|
Controls and Indicators - Front Panel |
- RESET Button:
- Recessed pushbutton
- Press to initiate a 'warm restart' causing the processor to reset,
but not lose power. A reset does NOT affect the current settings
- ID Button:
- Recessed pushbutton
- Press to send a notification out on the network to identify the unit
(the notification causes a pop-up dialog in N-Able and N-Command)
- POWER LED:
- On solid (green) when operating power is supplied (via PoE or local power supply)
- This activity is also shown by the PWR LED on the rear panel
- STATUS LED:
- On flashing (green) when there is software activity
- This activity is also shown by the STAT LED on the rear panel
|
Controls and Indicators - Rear Panel |
- PWR LED: Same as POWER LED described above
- HDMI LED: On (green) when there is a connection to a valid video source
- STAT LED: Same as STATUS LED described above
- STRM LED: On (green) when the unit is streaming video
|
Environmental |
- Temperature: 32° to 104°F (0° to 40°C)
- Humidity: 10% to 90% RH (non-condensing)
- Heat Dissipation: Up to ~44 BTU/hr
|
General |
- Regulatory Compliance: FCC, CE, and NTRL
- Recommended Accessories: NMX-ACC-N9206 (FGN9206), 2RU Rack Mount Cage with Power for Six SVSI N-Series Card Units
|
FG Numbers |
FGN1222A-CD |